What Types of Faucets Can a Plumber in Rosenberg Install in Your Home?

  • Are you unsatisfied with your current sink faucets in your home?
  • Have you just moved to a new home that has outdated sink faucets?
  • Did the sink faucet in a friend’s home catch your eye?
  • Do you plan to ask a plumber in Rosenberg to install new faucets?

If the answer is yes to any of the above-mentioned questions, you should look for modern sink faucets. Each faucet operates in a different manner. If you install two different faucets in your home, you can see for yourself how they are poles apart from each other.

Generally, this is not much of an issue. You should only know how to use them properly. However, when your faucet needs repair, you might be clueless. Before you have to contact a plumber in Rosenberg for fixing your faucet issues, equip yourself with the basic knowledge of how these faucets work.

Compression Faucets

Compression faucets are fairly old and belong to the previous generation of faucets which were routinely installed by an average plumber in Rosenberg. This faucet contains a disparate set of handles. In order to get cold or hot water, you just need to turn the handle in the correct direction. Water flow is managed by un-tightening or tightening handles with manual rotation. If you loosen the handle, water flows out. On the contrary, you can tighten the handle to limit the water flow.

A plumber in Rosenberg remarks that each faucet handle is connected by two stem assemblies; these are basically washer-based screws that positioned at the end. Stem assemblies are placed over the valve seat of the faucets, the source of the faucet’s water flow. You can drive the stem assembly down with the valve seat by simply closing off the faucet. Afterwards, compression of washer from the assembly with the valve seat terminates the water flow. If you turn on the faucet again, the washer can initiate the water flow again.

Ball Faucets

Ball faucets are those in which the handle of the faucet is semi-rotatable both side-to-side and up-and-down.  The objective behind the construction of ball faucets was to create a faucet that operates without a washer. These faucets consist of a single handle that can turn on either cold or hot water supply. You can often notice them in kitchen sinks. According to a reliable plumber in Rosenberg, the position of the ball faucets indicates the water’s flow rate, pressure, and temperature.

An experienced plumber in Rosenberg explains thatin ball faucets, a rotating ball—known as the lever ball assembly—is controlled by the handles. The assembly is situated within the body of the faucet. A spring and inlet-based system supports the assembly—it is placed over the faucet’s opening that lets the water to come out. Slots and chambers abet the ball. Each of these slots is responsible for the cold and hot inlet seats. If you can maneuver the ball, you can align the balls’ slots and gain the control of the water flow via the faucet.

Disc Faucets

If you call out a plumber in Rosenberg for faucet installation, they may use disc faucets—trendier and more modern than the ball and compression faucets. They are without washers, just like the ball faucets. They also have increased tensile strength—resistant to wear and tear— in comparison to both the former two faucet types. You can distinguish them with their cylindrical design and wider body. You can turn it side-to-side or up-down for water flow, although they don’t provide the same free motion as you can get from the ball faucets.

According to a renowned plumber in Rosenberg, these faucets consist of two disc: a lower disc and an upper disc. The lower disc is fixed while the upper disc is rotatable by using the handle. When you press both of these discs together, it results in a watertight seal, due to the flat nature of these discs. If you let water flow out by opening the faucet, the upper disc gets away from the fixed lower discs. This newly-generated gap allows the water to flow as long as the faucet remains open.

Cartridge Faucets

Cartridge faucets may have a single or double handles. These handles do not rely on rotatable handles to manage the water flow. All you need to do is turn and adjust a cartridge handle to let the water come out of the faucet. Meanwhile the handle moves to “on” state from the “off” state with a slick and smooth motion. A reputable plumber in Rosenberg explains that cartridge faucets with single handles are adjustable with side-to-side and up-to-down maneuvering to control temperature and the water flow.

Going by the explanation of a popular plumber in Rosenberg, the internal structure of these faucets comprise of a hollow metal cartridge. You can seal the faucet with the use of the hollow cartridge, restricting the water flow from both the cold and hot water lines. You can simply exert forward push for opening the cartridge faucet. In this new positioning, the water lines are not covered by the cartridge anymore, allowing the water to flow easily with its faucet. If you want to set the temperature, you can rotate the cartridge such that it can limit the hot water and cold water intakes.

Learning how faucets work in general can be extremely helpful while looking for new faucets. However, in order to install them, you are in need of a highly professional and experienced plumber in Rosenberg—someone who has all the necessary accreditations, licenses, and insurances. For this purpose, there are fewer businesses that that can fit the ball. Among them, Benjamin Franklin Plumbing® of Rosenberg stands tall. For the past few years, Benjamin Franklin has offered services to several happy clients in Rosenberg.